Book A Service Call

 

 

What're your thoughts with regards to How to Install a Bathtub Yourself?

Mounting a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably hard project. If the old tub is conveniently easily accessible, the task can move quickly; if you need to open up a wall surface to remove the old bathtub as well as place the new tub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will require a helper to move out the old tub and set in the new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your shower room if you have actually currently gotten a brand-new tub as well as don't need to change the arrangement of your previous water supply pipes.
Your devices and also product list must make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic due to the limited accessibility that is commonly the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipes. Once the supply pipelines have actually been gotten rid of, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Touches

If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washers are in area between the faucet and the sink. Protect the faucet in place with the supplier provided backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet ends first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Installing the Tub

Making use of the two wooden boards under its feet, put the bath tub in the required setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the level checks out level.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water system and also examine all joints and new pipework for leaks and tighten them if required. Fill up the tub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the tub must wait up until the bathtub has been utilized a minimum of once as this will settle it into its final setting.

 

 

Getting ready for the Installment

First of all, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last setting.

 

 

Tiling Around the Bathtub

In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, bring about complications with moisture and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water before sealing, to permit the motion experienced when the bathtub remains in use. The sealant can crack relatively early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive and also grout.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

Do you enjoy more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave feedback further down. We'd be interested to know your feelings about this write up. Hoping that you come back again in the near future. Sharing is caring. You never know, you may just be doing someone a favor. Thanks a lot for your time. Kindly stop by our blog back soon.

Go Services